ATV - UTV Trailer Parts

Stock# 1672128
TecNiq offset license plate bracket designed for use with all tail lights that mount with studs or bolts on 2" centers.

Stock# 1672127
TecNiq license plate bracket designed for use with all tail lights that mount with studs or bolts on 2" centers.

Stock# 7102082
Length - 40", Height - 11", Width - 10", Inside Length - 28". With round fender light cutouts on both front and back.
TRITON high impact gray composite fender fits Triton AUT 64 and 82 series ATV/Utility trailers.

Stock# 7102089
Overall Length = 71.25" Hub Face = 67.25" Bracket Center = 52.5"
TRITON axle weldment includes mounting hardware, hubs, bearing lube caps, bearings, seal and dust cap. Lug nuts sold separately.

Stock# 7102120
TRITON Aluminum Ramp Support for UT 12 and UT 16 series trailers is designed to help support the ramp gate. This support measures 34" overall length with a 32-1/2" mounting center. The tube is 1-1/2" x 1".

Stock# 7102080
TRITON aluminum weldment ramp support is designed to aid in supporting the ramp on Triton Utility and ATV trailers.  This support measures 31-3/4" overall length with a 30-7/8" mounting center. The tube is 1" x 1".

Stock# 7102088
TRITON Aluminum Floor Hinge Support is mounted on the trailer side of the ramp trailer connection. This support helps connect the ramp to the trailer and allows it to pivot open and closed.

Stock# 7102071
TRITON Quickslide Tie Down Kit comes with two quickslide I bolts to be used as tie down points. Tie down eyes come with quickslide keeper, a wing nut for tightening, a washer and a square reinforcement piece to add strength.

Stock# 7102070
TRITON Tie Down Flush mount kit includes a pair of 4" diameter round floor mount D-rings and mounting hardware.  Load limit is rated at 1,000 lbs.

Stock# 7102076
TRITON ATV Aluminum Tide down kit is designed to mount in the bottom corner of some Triton ATV trailers.  There will be a recesses groove that run in the inside corner of the floor and wall edge.  This kit includes (2) tie down brackets and all of the hardware to install the brackets.

Stock# 7102073
TRITON D-Ring Tie Down Kit comes with 4 of the D-Ring and D-ring brackets. The kit also includes all of the necessary hardware to mount brackets to a Triton AUT series trailer with mounting channels in the floor or side rail. D-Ring Dimensions: ID=1" x 1-1/4"  OD= 1-7/16" x 1-9/16"

Stock# 7102072
TRITON Quickslide Plate Tie Down Kit comes with two tie down plates with quickslide mounting hardware. Large hook hole is 9/16" x 1-13/16" and small hook hole has a diameter of 9/16".

Stock# 7102126
TRITON insert nut with snap ring is used in many different applications on Triton trailers.  Some applications included their add a nut kit, or the tilt bed tensioner.

Stock# 7102147
TRITON Aluminum Stake Pocket Kit are used to add stake posts (not included) to a trailer to build removable fencing/walls around an open trailer. Pocket opening is 3.5" x 1.5".

Stock# 7102034
TRITON Aluminum Stake Pocket Kit comes with 10 stake pockets and all of the necessary hardware to mount them. Stake pockets are used to add stake post (not included) to a trailer to build removable fencing/walls around an open trailer. Pocket opening is 3.5" x 1.5".

Stock# 7102124
TRITON Torx Deck screw is 1/4" x 1" and is used on most Triton trailers for mounting the decking.

Stock# 7102122
TRITON U-Bolt Spare Trailer Tire Mount can be mounted to any 3" box tubing. The two plates designed to sandwich the nuts can be locked together using a padlock for added security. Will accept 4-lug or 5-lug rims.

Stock# 7102010
TRITON Aluminum Spare Trailer Tire Mount can be mounted several different ways based on the type of trailer. Accepts rims that are 5 lug on a 4.5" bolt pattern with a center hole larger then 2-5/8".

Stock# 7102077
TRITON AUT Ramp Pin can be found on most Triton AUT series trailers to help secure the ramp.  The shaft measures 3-1/2" x 3/8" and the lanyard measures 10".

Stock# 7102097
TRITON license plate light is designed to snap into a grommet or mounted bracket that accepts 2-1/2" wide lights.

Stock# 7102001
TRITON license plate bracket designed for use with all tail lights that mount with studs or bolts on 2" centers.

Stock# 7115191
CARRY-ON license plate bracket.

Stock# 7102090
TRITON license plate bracket with light is designed for use with all tail lights that mount with studs or bolts on 2" centers.

Stock# 7102052
TRITON Flat 4-Prong 10' Leader Harness has a vehicle end and trailer end to extend the connection when needed.

Stock# 7102130
TRITON Flat 4-prong  wiring harness is specifically designed to fit XT Series and model LT10-101WB

Stock# 7102129
TRITON Flat 4-prong  wiring harness is specifically designed to fit model LT10, Elite10, and XT10VR.

Stock# 7102136
TRITON vinyl trim package is a decorative trim that is designed to cover up screws and keep debris out of areas around doors and hinges. It is 1" wide and comes in a 20' roll.

Stock# 7102132
TRITON wheel mounting studs have 1/2-20 hub thread and 1/2-20 nut thread and are 2" in total length.  The are designed to help utilize a bolt style hub as a stud style hub.

Stock# 7155052
TPS Aluminum Spare Trailer Tire Mount can be mounted several different ways based on the type of trailer. Accepts rims that are 6 lug on a 5.5" bolt pattern with 1/2" studs and fits frames that measure 5" in height. Hardware is NOT included.