EZ-LOADER Boat Trailer Rollers and Roller Hardware

Stock# 5291104
EZ-LOADER 15" bent aluminum arm roller assembly with gray non-marking 4-7/8" diameter x 3-1/2" wide wobble roller.

Stock# 5291036
EZ-LOADER two wobble roller assembly on a 15" x 1-1/4" x 3/4" aluminum arm with gray non-marking rollers. Also 13" from outside of roller to the outside of the other roller.

Stock# 5291168
EZ-LOADER double wobble roller assembly on 20" long bent aluminum arm.

Stock# 5291102
EZ-LOADER 4-wobble roller quad assembly on 15" aluminum arms with gray non-marking rollers.

Stock# 5291002
EZ-LOADER boat trailer wobble roller with ribbed gray non-marking design fits all EZ-Loader wobble roller trailers.
4-7/8" diameter, 3-1/2" width, 1-1/4" shaft, 1-1/4" bearing length

Stock# 5291170
EZ-LOADER mounting bracket for bunks boards and Double or Single roller arm assemblies. This mounting bracket will allow the bunk/roller arm to pivot as needed. Holes = 3/8"

Stock# 5291186
EZ-LOADER galvanized pivot bar mounting plate is attached to the cross-member with u-bolts and the pivot bar is sandwiched between two of these plates using 1/2" x 3-1/2" bolts. Sold as each.

Stock# 5291187
EZ-LOADER galvanized pivot bar mounting plate attaches to the cross-member and holds the front and rear cross-member that attach the roll system on larger trailers. Measures 7" and hast three height adjustment holes. Sold as each.

Stock# 5291200
EZ-LOADER galvanized upright supports brackets for both bunk and roll trailers with 3" wide cross-members and is 9" tall.

Stock# 5291201
EZ-LOADER galvanized upright supports brackets for both bunk and roll trailers with 3" wide cross-members and is 12" tall.

Stock# 5291182
EZ-LOADER 2" wide x 2" tall x 23.88" long .120" thick hot dip galvanized roller pivot bar mounts front-to-back over trailer crossbar. Used to support wobble roller assemblies on boat trailers.

Stock# 5291164
EZ-LOADER aluminum 15" single bent roller arm is for use with double-single slide arms. Meant to carry one roller on one end only. End is pre-drilled to accept hog ring fasteners.

Stock# 5291162
EZ-LOADER aluminum double roller arm is for use with 'multiple" roll systems. Will hold 2 rollers, one on each end. Attaches in the center to an aluminum arm. Ends are pre-drilled to accept hog ring fasteners and are to be used with 1" rollers.

Stock# 5291169
EZ-LOADER aluminum double roller arm is 20" in length and is to be used with a roller on each end. It has a center hole drilled to allow left-right pivoting. Ends are pre-drilled to accept hog ring fasteners.

Stock# 5291123
EZ-LOADER Galvanized steel bunk/roller mounting tray bolts to support brackets to attach bunk or roller assemblies and set proper angle. Bracket measures 4" wide x 30" long.

Stock# 5291133
EZ-LOADER boat trailer 25-3/4" x 1/2" hex head roller assembly through bolt.

Stock# 5291134
EZ-LOADER boat trailer 37-7/8" x 1/2" hex head roller assembly through bolt.

Stock# 5291160
EZ-LOADER boat trailer 3-1/2" x 2-1/4" roller bracket retaining plate. Used with EZ-Loader u-bolt #290-021938 (Sku #5291159) to attach roller assemblies. Mounting hardware and u-bolt sold separately.

Stock# 5291004
EZ-LOADER Cast aluminum roller assembly arm for Right Front or Left Rear boat trailer locations.
SUPPLIES LIMITED

Stock# 5291105
EZ-LOADER plated mounting strap and bolt kit attaches Quad-Roller assembly to pivot bar.

Stock# 5291103
EZ-LOADER 6-7/8" long x 2-3/4" wide galvanized wobble roller rocker plate. Plate rests on nylon glide (not included).

Stock# 5291033
3" long x 1-3/8" wide poly slide wedge fits EZ-LOADER roller arm assemblies. Flat bottom and concave top.

Stock# 5291041
EZ-LOADER nylon wobble roller bushing fits the newer Quad Roller assemblies.
Dimensions:  3/4" I.D. x 1-5/16" O.D. x 1-1/8" long

Stock# 5291037
EZ-LOADER nylon wobble roller bushing fits the gray ribbed roller.
Dimensions:  1" I.D. x 1-1/4" O.D. x 1-1/8" long

Stock# 5291100
EZ-LOADER 1-3/4" long x 1" O.D. x 3/4" I.D. spacer bushing for quad roller assembly.

Stock# 5291038
EZ-LOADER 1" I.D. x 2" O.D. wobble roller stainless steel washer.

Stock# 5291042
EZ-LOADER 5/8" I.D. x 1-1/2" O.D. wobble roller washer.

Stock# 5291040
EZ-LOADER hog ring secures boat trailer wobble rollers to arm and shaft assemblies. 13/16" I.D. x 1-1/2" O.D. before being compressed onto the roller arm.

Stock# 5291159
EZ-LOADER boat trailer 3/8" x 3/4" x 2" u- bolt. Mounting hardware sold separately.