Cam Lock Kits and Replacement Parts

Stock# 1660015
CAR MATE replacement cam lock bar includes 2 hinges and black vinyl grip for the handle. The handle measures 11-3/4" to the rivet holding the bracket and the shaft is 36-3/8" over all.

Stock# 1326288
BUYERS PRODUCTS Cam Action Door Lock Kit with rugged cast cups and lugs combined with a 13-1/2" steel handle and supports offer simplified installation and low cost for use with 3/4" pipe. Shown with pipe (not included)

Stock# 7107118
BIG TEX Aluminum Cam Door Lock Kit is a universal type lock kit that is designed to be used with a 3/4" pipe (not included). This kit can be mounted on flush to 3/4" offset doors and the bridge type keeper will prevent accidental opening.

Stock# 1577076
Zinc plated dump trailer cam lock kit with keeper has black vinyl grip and is riveted, not bolted to handle lug for added security. Bushing assembly supplied with non-removable pin for maximum security.
NOTE: Supplied without padlock or 3/4" pipe. Installation requires hinges and handle to be welded to pipe.

Stock# 1577079
The 257 Series all steel cam side door lock kit allows the entire length of pipe to cam over to secure doors. The 3/8" thick handle has black vinyl grip and is riveted, not bolted to handle lug for added security. Bushing assembly supplied with non-removable pin for maximum security.

Stock# 1577084
This replacement cam lock handle includes a pre-installed bracket and black vinyl grip. The handle measures 12-7/8" to the rivet holding the bracket.

Stock# 7107122
BIG TEX Zinc Plated Cam Door Handle comes with the u-bracket to mount it to the pivot pipe. The bracket is pre-mounted onto the handle and will allow the handle to swing up and down.

Stock# 7129031
PJ TRAILER replacement cam lock handle is powder coated black and includes pre-installed tabs that will need to be welded onto the gate. The handle measures 12-3/4" to the rivet holding the bracket and the shaft is 29-1/4" x 1-1/8".

Stock# 7122072
CAM SUPERLINE replacement cam lock handle includes a pre-installed bracket and black vinyl grip. The handle measures 13-1/4" to the rivet holding the bracket and the shaft is 19-5/8".

Stock# 7108631
The Rockwell American Rear Door Latch Kit is an ideal latch system for stock trailers. The 3 piece kit includes a 38" steel bar, handle and catch. Mounting hardware sold separately.
SUPPLIES LIMITED

Stock# 1577085
Replacement black vinyl handlegrip for cam lock kits. Universal grip fits most cam-type door lock handles.

Stock# 7107126
BIG TEX Zinc Plated Cam Door replacement rubber grip for cam door lock handle. The replacement grip slides directly onto the handle for added protection and comfort.

Stock# 5445079
The Miner Style Lock Rod Guide measures 4.50" x 1.50" x 1.80" and has a hot-dip galvanized finish. Sold as each.
SUPPLIES LIMITED

Stock# 7107121
BIG TEX Zinc Plated Cam Door Top lug is a direct replacement for the Big Tex universal cam door lock system. This lug would mount on the topside of a 3/4" pipe and would pivot in the top keeper to secure door.

Stock# 7107124
BIG TEX Zinc Plated Cam Door Bottom lug is a direct replacement for the Big Tex universal cam door lock system. This lug would mount on the bottom side of a 3/4" pipe and would pivot in the bottom keeper to secure door.

Stock# 1577087
This galvanized bottom cup component is used with the 158 series dump trailer cam lock kit. The base measures 5" x 1-1/4" and the mounting holes are 4" on center. The top cup is sold separately.

Stock# 7107125
Big Tex Zinc Plated Cam Door Bottom Keeper is a direct replacement for the Big Tex universal cam door lock system. This keeper would mount on the bottom side of the system and would except the bottom lug for securing of the system.

Stock# 7122076
CAM SUPERLINE galvanized bottom cup component is typically used with dump trailer cam locks. The base measures 5" x 1-1/4" and the mounting holes are 4" on center. The top cup is sold separately.

Stock# 1660024
CAR MATE replacement cam lock pipe retainer measures 4-1/16" x 1-9/16" and the mounting holes are 2-7/8" on center. Bottom pipe retainer sold separately.
SUPPLIES LIMITED

Stock# 1577086
This galvanized top cup component is used with the 158 series dump trailer cam lock kit. The base measures 5" x 1-1/4" and the mounting holes are 4" on center. The bottom cup is sold separately.

Stock# 7107120
BIG TEX raw steel cam door top keeper is a direct replacement for the Big Tex universal cam door lock system. This keeper would mount on the topside of the system and would except the top lug for securing of the system.

Stock# 5445076
Miner style seal pin from FLEET ENGINEERS has a hot-dip galvanized finish. Sold as each.
SUPPLIES LIMITED

Stock# 1577082
Replacement trailer cam lock latch measures 5-1/2" x 1" and the mounting holes are 4-1/4" on center.

Stock# 1577083
Replacement cam lock latch measures 5" x 2" and the mounting holes are 4" on center.

Stock# 7107123
BIG TEX zinc plated cam hasp assembly comes with both pieces pre-attached as one unit. The lock holes on the hasp are 7/16" in diameter.

Stock# 7122077
CAM SUPERLINE replacement cam lock hasp measures 5-1/2" x 1" and the mounting holes are 4-1/4" on center.

Stock# 1660019
CAR MATE Replacement Cam Door Hasp Assembly comes with both pieces. The locking holes on the hasp are 1/2" in diameter and the mounting holes are 4-1/16" on center.

Stock# 5445078
FLEET ENGINEERS Miner style seal plate measures 5.13" x 2.00" x 1.80" and has a hot-dip galvanized finish. Sold as each.
SUPPLIES LIMITED

Stock# T5445086
FLEET ENGINEERS replacement lockrod pipe is constructed with .105″ wall galvanized steel. It has a 1.12" diameter and is 120" long.
Ships 'Truck Freight' and is subject to delivery service limitations. (Click Truck for details)
SUPPLIES LIMITED