PJ TRAILER Factory Ramps and Dump Doors

Stock# 7129166
PJ TRAILER ramp is used on most C4 and C5 trailers. Each ramp is rated for 10,000 lbs and will have the hook welded on the inside edge of the main channels. Sold as each.

Stock# 7129167
This ramp is used on most CC, B5, B6, B8, and C8 trailers. Each ramp is rated for 10,000 lbs and will have the hook welded on the inside edge of the main channels. Width between hooks is 10-1/4". Sold as each.

Stock# 7129180
PJ TRAILER ramp is used on most PJ dump models, D7, DL, DJ, D8, D9, DS, DN, DM, DH, D3. Each ramp is rated for 6,500 lbs and will have the hook welded on the inside edge of the main channels. Sold as each.

Stock# T7129175
PJ TRAILER stand up ramp with the adjustable height support leg. This ramp is typically used on CC,C8, B6, B8 straight deck trailers.
Ships 'Truck Freight' and is subject to delivery service limitations. (Click Truck for details)

Stock# T7129168
PJ TRAILER standard flip over ramp used on FD and FS trailers with a dovetail. Typically used with a double hinge assembly.
Ships 'Truck Freight' and is subject to delivery service limitations. (Click Truck for details)

Stock# 7129172
PJ TRAILER Tri-Gate Left Hand Door for D7,DJ, D9, DL Dump Trailers. Comes in powder coated black finish but will NOT come with manufacturers decals.

Stock# 7129171
PJ TRAILER Tri-Gate Right Hand Door for D7,DJ, D9, DL Dump Trailers measures 40.5"W x 27"H. Comes in powder coated black finish but will NOT come with manufacturers decals.

Stock# 7129205
PJ TRAILER autolocking right hand door holdback only is used to keep gate doors from swinging closed.

Stock# 7129204
PJ TRAILER autolocking left hand door holdback only is used to keep gate doors from swinging closed.

Stock# 7129203
PJ TRAILER autolocking door holdback pin only is used to keep gate doors from swinging closed.

Stock# 7129083
PJ TRAILER black painted torsion ramp spring with 90 degree leg angle is designed for a shaft no larger in diameter then 1-3/4".

Stock# 7129086
PJ Trailer black painted left hand torsion ramp spring with 180 degree leg angle is designed for a shaft no larger in diameter then 1-3/4".

Stock# 7129087
PJ Trailer black painted right hand torsion ramp spring with 180 degree leg angle is designed for a shaft no larger in diameter then 1-3/4".

Stock# 7129081
PJ TRAILER black painted hand torsion ramp spring with 180 degree leg angle is designed for a shaft no larger in diameter then 1".

Stock# 7129058
PJ Dump / Tilt Trailer greaseable steel hinge strap with 2-3/8" leg in a 5/16" thick hinge housing.

Stock# 7129041
PJ TRAILER formed steel hinge strap with short leg includes zinc washers, hex head bolt, and locknut.

Stock# 7129031
PJ TRAILER replacement cam lock handle is powder coated black and includes pre-installed tabs that will need to be welded onto the gate. The handle measures 12-3/4" to the rivet holding the bracket and the shaft is 29-1/4" x 1-1/8".

Stock# 7129089
PJ Trailer ramp assist spring is raw steel and measures 3-1/2' x 14" over-all.

Stock# 7129173
PJ TRAILER stabilizer bar holds the ramps in an upright position for travel. The bar is 3/8" thick, 2" wide, and 36" long with holes on ends for quick pin. Powder coated black finish.

Stock# 7129169
These are used with the standard and HD flip-over dovetail ramps on all PJ Trailer models FD, LD, FS, and LS. It is the link between flip-over ramps and the rear bumper of the dovetail. Typically used with a dove tail ramp (160211).

Stock# 7129149
PJ TRAILER support leg prevents dump trailers from lifting up on the tailgate of the pickup when loading equipment and can be adjusted all the way up when not in use. Measures: 30" x 1.5" x 1.5", is powder coated black, and sold as each.

Stock# 7129148
PJ Trailer collar that is welded to bottom of bumper that the support leg slides and locks into.
SUPPLIES LIMITED

Stock# 7129077
PJ Trailer Ramp Gate latch bracket is used to latch a gate closed and it measures 2" x 3/8" x 2-5/8".

Stock# 7129075
Ramprod keeper for 1.5" diameter rods. This is a 4" tall ramprod keeper that can be used on the back bumper of a trailer. The opening is roughly 2" in diameter, 5" tall, 3/8" thick and 2-3/4" wide.

Stock# 7129073
Ramprod is 34" in length and 1.5" in diameter. For use with UH or CC trailers.

Stock# 7129080
PJ Trailer 1" pin that is used to connect a rampgate to the trailer allowing it to fold forward into the floor of the empty trailer.

Stock# 7129090
PJ Trailer Gate keeper end cap comes with 2 set screws and is intended to be used with a 1" shaft.